Manual de utilizare Conergy S 175MU

5.4 · 1
PDF manual
 · 2 pagini
manualConergy S 175MU

Installation | Safety instructions | Maintenance

Photovoltaic modules user manual

Conergy S 175/180MU/Conergy Q 85MU

Purpose of this guide
This guide contains information regarding the installation and safe handling of
Conergy photovoltaic modules (hereafter referred to as "modules"). All
instructions should be read and understood before attempting installation. If there
are any questions, please contact your dealer or Conergy for further information.
The installer should conform to all safety precautions in the guide when installing
modules. Before installing a solar photovoltaic system, the installer should
become familiar with the mechanical and electrical requirements for photovoltaic
systems. Keep this guide in a safe place for future reference.
| Installing solar photovoltaic systems requires specialized skills and knowledge.
The installer assumes all risk of injury, including risk of electric shock. Module
installation should be performed only by qualified persons.
| All modules come with a permanently attached junction box and #12 AWG
(4 mm²) wire terminated in Multi Contact PV connectors. Your dealer can
provide additional extension cables to simplify module wiring.
| Each individual module can generate DC voltages greater than 30 volts (V)
when exposed to direct sunlight. Contact with a DC voltage of 30 V or more is
potentially hazardous. Exercise caution when wiring or handling modules
exposed to sunlight.
| When disconnecting wires connected to a photovoltaic module that is exposed
to sunlight, an electric arc may occur. Arcs can cause burns, start fires or
otherwise create safety problems. Exercise caution when disconnecting wiring
on modules exposed to sunlight.
| Photovoltaic solar modules convert light energy to direct-current electrical
energy, and are designed for outdoor use. Proper design of support structures
is the responsibility of the system designer and installer.
| Modules may be ground mounted, pole mounted, or mounted on rooftops.
Do not attempt to disassemble the module, and do
not remove any attached nameplates or components.
Doing so will void the warranty.
| Do not apply paint or adhesive to the module.
Do not use mirrors or other hardware to artificially
concentrate sunlight on the module.
| When installing modules, observe all applicable local, regional and national
codes and regulations. Obtain a building and/or electrical permit where required.
Safety precautions for installing a solar photovoltaic system
| Solar modules produce electrical energy when exposed to sunlight.
DC voltages may exceed 30V on a single exposed module.
| Only connect modules with the same rated output current in series.
If modules are connected in series, the total voltage is equal to the sum of
the individual module voltages.
| Only connect modules or series combinations of modules with the same
voltage in parallel. If modules are connected in parallel, the total current is
equal to the sum of individual module or series combination currents.
| Keep children well away from the system while transporting and installing
mechanical and electrical components.
| Completely cover all modules with an opaque material during installation to
prevent electricity from being generated.
Do not wear metallic rings, watchbands, ear, nose, or
lip rings or other metallic devices while installing or
troubleshooting photovoltaic systems.
Use appropriate safety equipment (insulated tools,
insulating gloves, etc) approved for use on electrical
| Observe the instructions and safety precautions for all other components
used in the system, including wiring and cables, connectors, DC-breakers,
mounting hardware, inverters, etc.
| Use only equipment, connectors, wiring and mounting hardware suitable for
use in a photovoltaic system.
| Always use the same type of module within a particular photovoltaic system.
| Under normal operating conditions, PV modules will produce currents and
voltages that are different than those listed in the date sheet. Data sheet
values are applicable at standard test data.
| Short-circuit current and open-circuit voltages should be multiplied by a factor
of 1.25 when determining component voltage ratings, conductor ampacity,
fuse sizes and size of controls connected to the module or system output.
Refer to Section 690-8 of the National Electrical Code (NEC) for an additional
multiplying factor of 125 percent (80 percent de-rating) which may be applicable.
General installation notes
| Drainage holes must not be covered with parts of the mounting system. The
junction box has a breather port which must be mounted facing downward and
cannot be exposed to the rain. The junction box should be on the higher side of
the module when it is mounted in order to orient the breather port correctly.
| Do not lift the module by grasping the module's junction box or electrical leads.
| Do not stand or step on module.
| Do not drop the module or allow objects to fall on the module.
| Do not place any heavy objects on the module.
| Inappropriate transport and installation may damage the module glass or frame.
Mechanical Installation
Selecting the location
| Select a suitable location for installation of the module.
| For optimum performance, the module must be facing true south in northern
latitudes and true north in southern latitudes.
| For detailed information on optimal module orientation, refer to standard solar
photovoltaic installation guides or a reputable solar installer or systems integrator.
| The module should not be shaded at any time of the day.
| Do not install the module near equipment or in locations where flammable gases
can be generated or collected.
Selecting the proper mounting structure and hardware
| Observe all instructions and safety precautions included with the mounting
system to be used with the module.
| Do not drill holes in the glass surface of the module. Doing so will void the warranty.
| Do not drill additional mounting holes in the module frame. Doing so will void the
| Modules must be securely attached to the mounting structure using four
mounting points for normal installation. If heavy wind or snow loads are
anticipated, additional mounting points should also be used. Please see the
drawing below.
| Load calculations are the responsibility of the system designer or installer.
| The mounting structure and hardware must be made of durable, corrosion- and
UV-resistant material.
Mounting methods
1. Mounting With Bolts
| The module must be attached and supported by at least four bolts through
the indicated mounting holes.
| Most installations will use the four inner mounting holes on the module frame.
| Depending on the local wind and snow loads, additional mounting points may
be required.

Please carefully read the following installation and safety instructions.

Non-compliance with these instructions may void the module warranty.

Page 1/2


Consultați aici manualul pentru Conergy S 175MU, gratuit. Acest manual se încadrează în categoria Panouri solare și a fost evaluat de 1 persoane cu o notă medie de 5.4. Acest manual este disponibil în următoarele limbi: Engleză. Aveți o întrebare despre Conergy S 175MU sau aveți nevoie de ajutor? Puneți întrebarea aici

Aveți nevoie de ajutor?

Aveți o întrebare despre Conergy și răspunsul nu se află în manual? Puneți întrebarea aici. Furnizați o descriere clară și cuprinzătoare a problemei și a întrebării dvs. Cu cât problema și întrebarea dvs. sunt descrise mai bine, cu atât le va fi mai ușor celorlalți proprietari Samsung Galaxy A7 să vă ofere un răspuns bun.

Numărul de întrebări: 0

Specificații Conergy S 175MU

Mai jos veți găsi specificațiile produsului și specificațiile manuale ale Conergy S 175MU.

Brand Conergy
Model S 175MU
Produs Panou solar
Limbă Engleză
Tipul fișierului PDF

Întrebări frecvente

Nu puteți găsi răspunsul la întrebarea dvs. în manual? Puteți găsi răspunsul la întrebarea dvs. în Întrebările frecvente despre Conergy S 175MU de mai jos.

Întrebarea dvs. nu se regăsește aici? Puneți întrebarea aici

Fără rezultate